Lỗi place doc feeder in the down position toshiba 283 năm 2024

Brand: Select model: Toshiba e-Studio 355 Trouble Error Codes ListService manual Download the full PDF version of service manual.CodeDescriptionPaper exit jamE010Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor.E020Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor.Other paper jamE030Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.E061Incorrect paper size setting for upper drawer: The size of paper in the 1st drawer differs from size setting of the equipment.E062Incorrect paper size setting for lower drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.E063Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.E064Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.E065Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipmentE090HDD abnormality causes jam: Image data to be printed cannot be prepared.Paper misfeedingE110ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printingE120Bypass misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the bypass tray does not reach the 1st transport sensorE130Upper drawer misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the upper drawer does not reach the 1st transport sensor.E140Lower drawer misfeeding (Paper not reaching the 2nd transport sensor): The paper fed from the lower drawer does not reach the 2nd transport sensor.E150PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.E160PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensoE190LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.Paper transport jamE200Upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.E210Lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensorE220Lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the lower drawer feed sensor.E270Bypass transport jam (paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.E280ADU transport jam (paper not reaching the registration sensor): The paper which has passed through ADU and the 1st transport sensor does not reach the registration sensor during duplex printingE300PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1s

t transport sensor.E310PFP upper drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.E320PFP upper drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.E330PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.E340PFP lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the PFP lower drawer feed sensor.E350PFP lower drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.E360PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor.E3C0LCF transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.E3D0LCF transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.E3E0LCF transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the LCF feed sensor.Cover open jamE410Front cover open jam: The front cover has opened during printing.E420PFP side cover open jam: The PFP side cover has opened during printing.E430ADU open jam: The ADU has opened during printingE440Feed cover open jam: The feed cover has opened during printing.E450LCF side cover open jam: The LCF side cover has opened during printing.E480Bridge unit open jam: The bridge unit has opened during printing.E490Job separator cover open jam: The job separator cover has opened during printing.E491Offset tray cover open jam: The offset tray cover has opened during printing.Paper transport jam (ADU section)E510Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section.E520Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor.Other paper jamE550Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding).E570Jam not reaching the reverse sensor: The paper which has passed the exit sensor does not reach the reverse sensorE580Stop jam at the reverse sensor: The trailing edge of the paper does not pass the reverse sensor after its leading edge has reached this sensorRADF jamE712Jam not reaching the registration sensor: The original fed from the original feeding tray does not reach the registration sensor.E714Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.E721Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).E722Jam not reaching the exit sensor (during scanning): The original which p

assed the read sensor does not reach the exit sensor when it is transported from the scanning section to exit section.E724Stop jam at the registration sensor: The trailing edge of the original does not pass the registration sensor after its leading edge has reached this sensor.E725Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.E731Stop jam at the exit sensor: The trailing edge of the original does not pass the exit sensor after its leading edge has reached this sensor.E860RADF jam access cover open: The RADF jam access cover has opened during RADF operation.E870RADF open jam: RADF has opened during RADF operation.E871Cover open jam in the read ready status: Jam caused by opening of the RADF jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment.Finisher jam (Bridge unit)E910Jam at the bridge unit transport sensor-1: The paper does not reach the bridge unit transport sensor-1 after it has passed the exit sensor.E920Stop jam at the bridge unit transport sensor-1: The trailing edge of the paper does not pass the bridge unit transport sensor-1 after its leading edge has reached the sensor.E930Jam at the bridge unit transport sensor-2: The trailing edge of the paper does not reach the bridge unit transport sensor-2 after its leading edge has reached the bridge unit transport sensor-1.E940Stop jam at the bridge unit transport sensor-2: The trailing edge of the paper does not reach the bridge unit transport sensor-2 after its leading edge has reached the bridge unit transport sensor-2.Job separator jamE950Jam not reaching the job separator transport sensor: The paper has passed through the exit sensor does not reach the job separator transport sensor.E951Stop jam at the job separator transport sensor: The trailing edge of the paper does not pass the job separator transport sensorOffset tray jamE960Jam not reaching the offset tray transport sensor: The paper has passed through the exit sensor does not reach the offset tray transport sensor.E961Stop jam at the offset tray transport sensor: The trailing edge of the paper does not pass the offset tray transport sensor.Finisher jamE9F0Punching jam: Punching is not performed properly. [MJ-1025 (When MJ-6005 is installed)] Punching jam: Punching is not performed properly. [MJ-1024 (when MJ-6004 is installed)] [MJ-1101 (when MJ-6101 is installed)]EA10Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. [MJ-1024/1031/1101]EA20Paper transport stop jam: The paper does not pass through the inlet sensor. [MJ-1025/MJ-1031] Paper transport stop jam: The paper has passed through the inlet sensor but does not reach or pass the feed path sensor or processing tray sensor. [MJ-1024] Paper transport delay jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ- 1101EA21Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec.EA22Paper transport jam (Finisher paper punching edge detection sensor)EA23Paper transport jam (exit sensor)EA24Paper transport jam (between entrance and exit sensors)EA25Paper transport jam (after paper stack exit)EA26Paper transport jam (stop command request)EA27Paper transport jam (paper not inserted)EA28Paper transport jam (assisting arm operation delay)EA29Paper transport jam (stack transport delay)EA30Power-ON jam: Paper exists at the inlet sensor when power is turned ON.