Remove the paper from internal tray 1 ricoh 3352 lỗi năm 2024

hướng dẫn xử lý kẹt giấy máy in - lỗi Misfeed: Tray 1 hoặc Misfeed: Tray 2

Lỗi máy in Ricoh

Lỗi kẹt giấy máy in ricoh

When “Internal Misfeed”, “Misfeed: Tray 1”, “Misfeed: Tray 2”, or “Misfd: Stnd Tray” Appears

When “Internal Misfeed”, “Misfeed: Tray 1”, “Misfeed: Tray 2”, or “Misfd: Stnd Tray”Appears

“Internal Misfeed”, “Misfeed: Tray 1”, “Misfeed: Tray 2”, or “Misfd: Stnd Tray” appears when a paper jam has occurred in the fusing unit, tray 1, or tray 2.

Use the following procedure to remove paper that has become jammed inside the printer or in the paper feed area.

1. Pull tray 1 halfway out, and check for jammed paper. If there is jammed paper, remove it carefully.

2. Carefully slide tray 1 back in until it stops.

3. If paper is loaded in the bypass tray, remove the paper.

4. Close the bypass tray.

5. Push the side button to open the front cover, and then carefully lower it.

kẹt giấy máy in ricoh

6. Carefully pull out the print cartridge horizontally, holding its center.

lỗi misfeed ricoh

  • Do not shake the removed print cartridge. Doing so can cause remaining toner to leak.
  • Place the print cartridge on paper or similar material to avoid dirtying your workspace.

7. Lifting the guide plate, remove the jammed paper carefully.

8. Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place.

lấy kẹt giấy máy in ricoh

9. Using both hands, carefully push up the front cover until it closes.

sửa lỗi kẹt giấy máy in ricoh tại Hải Dương

lỗi xuất hiện như bên trên bản tiếng anh là nguyên nhân chính của việc vị kẹt giấy khi kéo đến trống bị kẹt lại.

hướng đi của giấy có thể bị kẹt vật nhỏ làm tắc đường đi của giấy, hoặc có mẩu giấy nhỏ [ cỏ thể sensor hỏng]

* If the optional HP Internal Battery is not installed in the printer, unplug the printer power cord. Wait about 10 seconds, then plug the power cord back in.

* If the optional HP Internal Battery is installed in the printer, unplug the printer power cord, if it is plugged in. Open the battery compartment cover and remove the battery. Wait about 10 seconds, then reinstall the battery. If desired, plug in the power cord.

Turn on the printer. The printer checks for paper in the paper path and will automatically eject the jammed paper. Press OK to continue.

If the paper came part way through the front of the printer, gently pull the paper towards you to remove it.

If the paper did not come part way through the front of the printer, try removing it from the back of the printer like this

1 Remove the paper from the In tray, then push in the catches to release the in tray.

2 Open the In tray to a horizontal position.

3 Gently pull the jammed paper to remove it from the back of the printer.

4. Before you lift the In tray to close it, make sure it is pushed all the way to the right on its hinges.

If “Internal Misfeed”, “Misfeed: Tray 1”, “Misfeed: Tray 2” appears on the display, follow the procedure below to remove it.

  • The inside of this machine becomes very hot. Do not touch the parts labeled "
    " [indicating a hot surface].

  • Some of this machine's internal components get very hot. For this reason, take care when removing misfed paper. Not doing so could result in burns.

  • When removing jammed paper, make sure not to trap or injure your fingers.

Pull tray 1 halfway out, and check for jammed paper. If there is jammed paper, remove it carefully.

Carefully slide tray 1 back in until it stops.

If paper is loaded in the bypass tray, remove the paper.

Close the bypass tray.

Push the side button to open the front cover, and then carefully lower it.

Carefully pull out the print cartridge horizontally, holding its center.

  • Do not shake the removed print cartridge. Doing so can cause remaining toner to leak.
  • Place the print cartridge on paper or similar material to avoid dirtying your workspace.

Lifting the guide plate, remove the jammed paper carefully.

Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place.

Using both hands, carefully push up the front cover until it closes.

  • If paper is jammed in tray 2 but is difficult to locate, pull out tray 2 to remove it. After removing the paper, carefully push tray 2 all the way back inside the machine.

When closing the front cover, push the upper area of the cover firmly. After closing the cover, check that the error is cleared.

Chủ Đề